How Do You Replace A 2002 Avalanche Rear Camera

Download Article

Download Article

A rear-view camera, as well known every bit a backup photographic camera, lets you see what'due south behind your vehicle without having to look backwards. Though the device comes standard with many new motorcar models, you can add a rear-view camera to your vehicle if it didn't come with one.

1. 1

   Buy a mountable backup camera for your specific vehicle. For safe, make sure you purchase a device specifically designed to be a rear-view camera. Purchasing one made for your specific vehicle will make it easier to install than a standard aftermarket camera. Then you lot can install information technology hands, look for a photographic camera that mounts onto or directly behind your license plate.^[1]

   • Expect for backup cameras at consumer electronics stores.

2. 2

   Go an external monitor if yous want to continue your existing rear-view mirror. An external fill-in monitor is a pocket-size video screen that mounts onto your windshield similarly to a GPS. Though they take upwards more space than internal monitors, external monitors are far easier to encounter and can be easily replaced if necessary.

   • If you'd similar, yous tin use a standard video monitor instead. However, keep in mind that it may not have all the same features as devices designed for utilise with backup cameras.

   Advertisement

3. 3

   Purchase an internal monitor for a less obtrusive device. An internal backup monitor is a fully operation rear-view mirror that houses a pocket-sized screen inside the glass. Some internal monitors clip on top of your current rear-view mirror, simply others replace your original mirror entirely.^[2]

   • Most internal monitors shut off and disappear when non in use, making them a perfect option if yous desire to preserve your automobile's looks.

4. 4

   Purchase power and video cords if your photographic camera and monitor didn't include them. For most rear-view camera installations, you lot'll need camera and monitor splitter cords with connectors for video and power cables, 2 bare wire power cables, and an RCA video cablevision.^[three]

   • Most installation kits include these cables, but some may require you to buy them separately.
   • Some camera models utilise wireless transmitters instead of standard video cables.

   Advertisement

1. 1

   Take off your rear license plate. Using a Phillips head screwdriver, remove each of the screws property your rear license plate in place. Then, pull the plate off and set up it bated.^[4]

   • Make sure you place the screws in a safe place so yous don't lose them.

2. two

   Remove your torso's interior panel. Pop open up your body and look for a solid interior panel roofing the opposite side of your license plate mounting area. Then, insert a trim removal tool or other thin device backside the panel and pry it off.^[5]

   • Removing this panel will expose the car's rear wiring chambers.

3. 3

   Drill a modest hole in the license plate mounting expanse. Make certain in that location are no obstructions between the license plate mount and the rear wiring chamber. Then, create a small pigsty in the car using a power drill equipped with a high-speed twist drill bit. Line up your hole and so it is directly behind where your camera'south power and video cable volition go.^[6]

   • To figure out where to make the hole, hold your camera up to the area y'all intend to mount it. Then, note the spot where its splitting cord sits.
   • Create a hole that'south big enough to fit your photographic camera'south power and video cable.
   • If you lot meet whatsoever obstructions, try to remove them. If you can't, run across if you tin make a hole nearby.
   • For most jobs, you'll demand a drill chip that has a diameter between ⁱ⁄_eight and ⁱ⁄₄  in (0.32 and 0.64 cm).

4. iv

   Place a rubber grommet around your photographic camera cable. Before running your camera cablevision into the auto, sideslip a safe grommet onto it almost the non-splitting cease. These small safety washers, available at near home comeback stores, volition proceed the wire in place and prevent leaks.^[7]

   • Choose a grommet that's just large enough to fit inside the drilled hole.

5. 5

   Run the camera cablevision into your trunk. Pull the splitting stop of your camera's video and power cable through the drilled hole into the body of your auto. Brand sure you pull it tight so the prophylactic grommet lodges into the drilled hole.

   • Your camera cablevision should run from the outside of the car to the within of the auto.

6. 6

   Locate your automobile's 2 reverse calorie-free wires. Reverse light wires are the cords that connect your automobile's tail lights to the dashboard. They hook direct into your vehicle's tail lights and are ordinarily located in the hatch or trunk of your car.

   • These cords expect different for every vehicle so, if y'all can't find them, consult your possessor'south manual for model specific data.

7. seven

   Strip and dissever your car's reverse low-cal wires. Using a wire stripper or pliers, skin back the safety covering the wires. Then, use a screwdriver or other thin tool to poke a hole through the middle of each exposed wire, separating the private wire strands.^[eight]

   • For safety, brand sure you do this while the car is turned off.

8. 8

   Fuse your camera wires with the contrary low-cal wires. Attach ane of your bare wire cables to the photographic camera cord'southward power connector. Then, poke your bare wires through the center of the exposed reverse light wires and twist them together. For safety, make sure you wrap the combined wires in electrical record.^[9]

   • Brand sure yous poke your positive (usually red) bare wire through the positive opposite light wire and the negative (usually blackness) bare wire through the negative reverse light wire.

   Advertisement

1. 1

   Route your camera'south video cable to the front of the car. Connect your RCA cablevision to the photographic camera cord'southward video connector if necessary. Then, run information technology through your vehicle to the surface area by the fuse box. Depending on your vehicle model, you'll usually exist able to practise this by peeling back the motorcar's headliner or side panels and pulling your cable through the exposed chamber.^[ten]

   • For sure trucks, you lot may need to run the video cable through the vehicle'due south frame rails.
   • In nigh cars, you'll find the fuse box underneath the steering wheel.

2. two

   Fix external monitors to the front end windshield. If you're installing an external monitor, first adhere your device's included mount to the windshield by post-obit the manufacturer'southward included instructions. And so, claw your monitor onto the mount.

   • Most external monitors employ a suction mountain, though others may come with a more complex mounting system.

3. 3

   Attach internal monitors to the rear-view mirror or mirror mount. For certain internal monitors, you'll need to clip the new device onto your current rear-view mirror. For others, yous'll need to take off the mirror and slide your monitor into the pre-existing mirror mount.^[11]

   • Some internal monitors may come with their own mounting organisation that you'll have to attach to the car's front end windshield.

4. 4

   Run the monitor's splitter cable to the fuse box. If necessary, hook your monitor'south power and video cable into the device. And so, route the cablevision from the monitor to the area next to the fuse box.^[12]

   • If yous'd similar, use a trim removal tool to pop out the headlining panel straight above your windshield. Then, run your cable through the exposed chamber.

5. 5

   Connect your monitor's photographic camera cable to the RCA cable. After routing your monitor's splitter cable, connect the video end of the cable to your camera's RCA cord. Then, wrap the connected cords with electrical tape to hold them together.

   • If your RCA and video cables accept the same ends, you may need to purchase an RCA male to female converter cord. You can find these at most electronic stores.

6. 6

   Attach your monitor'south power cable to a fuse tap. Connect your remaining bare wire cablevision to the fill-in monitor'due south power cord. Then, push the positive (usually red) terminate of the bare wire cablevision into the open terminate of a fuse tap. Finally, crimp the two cables together with a pair of pliers.^[thirteen]

   • A fuse tap is a small-scale cable that converts a blank wire into a fuse signal. You can find them at most auto part stores.
   • If y'all'd prefer, you can leave the bare wire cable off and connect your camera's ability cable to a cigarette lighter adaptor. And then, plug this adaptor into your motorcar's cigarette lighter receptacle for power.

7. 7

   Plug the fuse tap into the fuse box. Locate your fuse box and open it up. Then, plug your fuse tap into an open up fuse cell. If necessary, bank check your fuse box'south chapeau or your vehicle'due south instruction manual to run across which slots are open.^[fourteen]

   • After attaching your fuse, consider taping all your wires together using electrical tape to go them out of the way.

   Advert

1. ane

   Connect your fill-in camera to its power and video cable. Return to the back of your car once y'all've installed the rear-view monitor and all the necessary camera cords. Close the trunk if necessary, then connect the backup camera to its power and video cable.

   • Your camera's power and video cable should be sticking out of the hole you drilled in the license plate mounting area.

2. 2

   Mount the camera to your license plate. If the camera attaches to the front of your license plate, ready it to the plate by following the manufacturer's included instructions. If the camera attaches to the dorsum of your license plate, line the device upward with the plate's fastener holes and thread screws through them.^[15]

   • In well-nigh cases, you lot can attach a rear-view camera to the back of your license plate using the screws you removed from the motorcar earlier.

3. three

   Reattach your license plate and trim panels. Using a Phillips head screwdriver, put your rear license plate back on your vehicle. Once you've reattached it, requite the license plate and fill-in camera firm tugs to make sure they're secure.

   • If y'all haven't already, reattach your car's interior torso panel and other trim panels by pressing them back onto the vehicle.

4. 4

   Test the camera to brand sure everything works. Before using your new camera on public roads, exam it in a safe expanse similar your driveway. If information technology turns on, place a large, durable object similar a trash tin can behind the camera to see how distorted the image is. If it does not turn on, read your installation transmission for troubleshooting information.

   • In many cases, rear-view camera malfunctions are caused by loose or improperly connected wires.

   Ad

Add New Question

• Question

  I hooked the photographic camera upwards and it merely flickers. Any advice?

  

  You may desire to ensure all cables and connections are secured tightly. Double check that all connections are correct. If this doesn't work, check to meet if the camera called is in good shape and isn't physically damaged.

• Question

  Suzuki installed reverse parking camera in my Swift Dzire Zxi. But the camera shows upper view and not the ground below. What tin can I do ?

  

  Brand sure that the photographic camera is installed the correct way (not upside downward), and check the position of the camera mounted. Take it back to the dealer that installed it and ask them to check the alignment and fit.

• Question

  What is the best height for a reversing camera?

  

  There is no optimal height for a back-upwardly camera. The ideal superlative is based off the specific car or vehicle that you lot have and your personal preferences, along with its intended awarding. Some redundancy cameras are placed on large service trucks and then that they tin line upwards to trailer hitches easier, some are to prevent a blindspot on the road. Depending on your application, it tin be placed at any height. Most reversing cameras are a "wide view" manner and the specific meridian location does not e'er affect the mode it functions.

• Question

  So if I hooked up all the wires correctly but nevertheless no power, is information technology a fuse tap that I need to splice into the wires for information technology to piece of work correctly?

  

  Shannon Phillips

  Community Answer

  Check your earth or basis it may exist bad. Use your multimeter to see if the ground is okay.

• Question

  Is it still okay to connect the back-up camera to the reverse light with cars that have motorcar lighting? Or, would I need to connect to the opposite wire on the gearbox?

  

  Shannon Phillips

  Community Answer

  Yes, that will be fine, that how it is supposed to be washed. Wait for an auto electrician if you need someone to telephone call.

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advert

• Though most machine dealers and mechanics will not install aftermarket fill-in camera systems, many sound and electronic shops volition.

Advertizing

• Make sure you lot plough the car off earlier working with bare or stripped wires. If y'all need to touch on exposed wires while the car is on, put on a pair of shock-resistant rubber gloves.

Advertisement

Things You'll Need

• Rear-view camera
• Rear-view monitor
• Connector cables
• Phillips head screwdriver
• Trim removal tool
• Power drill with high-speed twist bit
• Rubber grommet
• Wire stripper or pliers
• Electrical tape
• Fuse tap

Nigh This Article

Article Summary X

To successfully install a rear-view camera, start remove your vehicle's rear license plate and interior trunk console. Using a power drill, punch a minor hole through the exposed license plate mounting surface area and run your camera's power and video cord through it. Attach a bare wire power cable to your camera's ability connector, then strip your car's reverse lite wires and splice them with your bare wire power cablevision. To learn how to mount the rear-view photographic camera and backup monitor, ringlet down!

Did this summary assist you?

Cheers to all authors for creating a page that has been read 260,993 times.

Did this commodity aid you?

Source: https://www.wikihow.com/Install-a-Rear-View-Camera

Posted by: churchwolleationg1967.blogspot.com

Share this post